Mira vigour User's Guide Page 1

1ManualThese instructions are to be left with the userPOWER SHOWERMANUALInstallation and User Guide

10Gravity Fed System - The shower MUST be fed from a cold water cistern and hot water cylinder providing nominally equal pressure.INSTALLATION REQUIRE

11INSTALLATIONGeneral1. Do not take risks with plumbing or electrical equipment.2. Do not install the shower unit in a position where it could becom

12Plumbing1. A minimum storage capacity of cold water of 230 litres (50 gallons) is required to provide adequate showering time. Insufcient storage m

13Warning! Do not x the shower unit to the wall until plumbing and electrical installations have been completed.1. Decide on a suitable

143. Make sure that the end of the supply pipework is cut squarely and is free from burrs, which will damage the inlet manifold seals. Chamfer the e

157. Temporarily locate the shower unit.8. Position the shower unit on the wall and mark the three xing points. Note! Installers may wish to obtain

1612. Fit the three rubber feet into the recesses in the rear of the case as shown. The feet will reduce the noise transmitted by the power shower th

1714. Locate the shower unit on the inlet supplies and push the inlet manifold onto the pipework until resistance is felt. DO NOT FORCE! Note! PTFE

1819. Ret the unit cover and secure with the three cover securing screws.20. Insert the ow control knob in the OFF position.21. Insert the

19COMMISSIONINGThe unit must not be run dry. Before proceeding any further with the installation the shower unit must be commissioned.1. Connect the

2CONTENTSIntroduction ...3Patents ...

20OPERATION1. Turn the outer ow control knob until the desired ow of water is obtained. The ow of water will increase the further the contro

21FAULT DIAGNOSISFault Diagnosis - User MaintenanceThe appliance is fully performance tested after assembly. Providing it has been correctly installed

22Fault Diagnosis - Installer MaintenanceThe Manual Power Shower is one part of an entire plumbing system. The tting of a pump places additional requ

23Malfunction Cause RemedyMaximum shower temperature too cold.Hot water cylinder temperature too low.Adjust cylinder temperature.Note! The stored wate

24Warning! There are no user serviceable components beneath the cover of the appliance. Only a competent tradesperson should remove the cover.Before

25SPARE PARTS147.67 Check Valve Pack453.02 Cartridge - Manual 453.03 Motor Pump Assembly - components identied ‘A’453.07 Inlet Manifold Assembly

26ACCESSORIESGenuine Mira accessories can be purchased direct from Customers Services (our contact details can be found on the back cover of this guid

27NOTES

281088850-W2-D (B85M) © Kohler Mira Limited, November 2010CUSTOMER SERVICEGuaranteeYour product has the benefit of our manufacturer’s guarant

3The Mira Vigour Manual Power Shower is an all-in-one power shower with an integral mains voltage pump, and separate controls for ow and temperature.

4IMPORTANT SAFETY INFORMATIONWarning!1. Read all of these instructions and retain this guide for later use.2. Products manufactured by us are sa

521. DO NOT commission this appliance if water leaks from the unit.22. DO NOT operate this appliance if water leaks from this appliance.23. Only a

6Caution!1. Read all of these instructions and retain this guide for later use.2. Make sure that this guide is left with the user. Pass on this guid

7PACK CONTENTS Tick the appropriate boxes to familiarise yourself with the part names and to conrm that the parts are included. 1 x Manual Power

8DIMENSIONSAll dimensions are nominal and in millimetres.282820201308866 80310210

9ElectricalPower Supply: 230 - 240 V at 50 Hz, fused at 3 Amps, via a double pole fused switch (not supplied) with a minimum contact separation of 3 m